Plumbing Essentials: A Prerequisite for Installing a Bathtub
Plumbing Essentials: A Prerequisite for Installing a Bathtub
Blog Article
On this page down the page you will find a lot of high-quality material involving How to Install a Bathtub.
Installing a bathtub isn't specifically brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately tough project. If the old bathtub is conveniently easily accessible, the task can move speedily; if you have to open up a wall surface to remove the old bathtub as well as place the new bath tub, the job is a lot harder. In either case, the task is within a home handyman's skills, although you will certainly require a helper to move out the old tub as well as embeded in the new one. Ensure you have actually qualified yourself for the job and are comfortable attempting it. Instead of employing a specialist to take control of a halfway-completed job, it is much better to think about utilizing one before you begin. Opportunities are you may require an expert plumber to make tube links.
This short article will aid you install a new bath tub in your restroom if you have currently purchased a new bathtub and also do not need to change the setup of your previous water pipelines.
Your devices as well as material list must comprise the following:
Getting ready for the Setup
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if required) according to the maker's instructions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the taps unit to prevent pressure on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet through the hole in the bathroom. Use the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the trap to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a comparable manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Taps
If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you must do is separate the supply of water. After doing so, activate the faucets to drain pipes any water staying in the system. The process of eliminating the existing taps can be rather troublesome due to the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipes to the faucets. Have a cloth ready for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have actually been eliminated, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the single faucets from turning during this procedure. Once the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old sealing substance.
Before moving on to fit the new faucets, contrast the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is needed for the brand-new faucets to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed setting. The wood boards are handy in evenly spreading the weight of the bathtub over the location of the boards rather than concentrating all the weight onto four little factors.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level as well as changing the feet on the tub up until the level reads degree.
To mount faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other tap.
Turn on the supply of water and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the tub and additionally inspect the overflow outlet and also the normal electrical outlet for leakages.
Finally, repair the bath paneling as defined in the maker's instruction manual. Tiling and also sealing around the bath tub must wait until the bathtub has actually been used a minimum of when as this will certainly settle it right into its last position.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipes.
If you need to fit a monobloc, then you will certainly call for reducing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin ensuring that the washing machines are in area in between the faucet and also the sink. Safeguard the faucet in position with the maker supplied backnut. When the faucet is securely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former kind needs to be linked to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bathtub
In the location where the bathroom fulfills the ceramic tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can move sufficient to fracture an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and also possible leaks to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, and also are capable of sealing voids up to a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched newspaper or soft rope. Keep in mind to constantly load the bathtub with water before sealing, to allow for the activity experienced when the tub is in use. The sealant can split relatively very early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally conveniently readily available on the marketplace. It is advisable to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that page on Tools You Need to Install a New Bathtub when doing a lookup on the internet. Sharing is nice. Helping others is fun. I am grateful for your time. Don't hesitate to check up our blog back soon.
Plumbing emergencies? Our experts await. Report this page